ADJ Dotz Bar 1.4 Specifications download pdf (Page 3)

Power Supply: The ADJ Dotz Bar 1.4 contains a automatic voltage

switch, which will auto sense the voltage when it is plugged into a

power source. With this switch there is no need to worry about the cor-

rect power voltage, this unit can be plugged in anywhere. Always use

the PowerCon cord that came with the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav-

els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

dierent manufactures to be linked together and operate from a single

controller, as long as all xtures and the controller are DMX compli-

ant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Dotz Bar 1.4 can be controlled via DMX-512 protocol. The Dotz Bar

1.4 has 5 DMX Channel Modes. The DMX address is set on the rear

panel of the Dotz Bar 1.4. Your unit and your DMX controller require

a approved DMX-512 110 Ohm Data cable for data input and data

output (Figure 1). We recommend Accu-Cable

DMX cables. If you are making your own cables,

be sure to use standard 110-120 Ohm shielded

cable (This cable may be purchased at almost

all professional sound and lighting stores). Your

cables should be made with a male and female

XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained

and cannot be split.

ADJ Products, LLC - www.adj.com - Dotz Bar 1.4 User Manual Page 5

Dotz Bar 1.4 Set Up

Figure 1

Dotz Bar 1.4 Safety Precautions

ADJ Products, LLC - www.adj.com - Dotz Bar 1.4 User Manual Page 4

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Do not attempt to remove or break o the ground

prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by

t he manufacturer. See page 21 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (inclu-

d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments

ADJ Dotz Bar 1.4 Specifications Page 3

Comments to this Manuals

Related products and manuals for Floodlights ADJ Dotz Bar 1.4