ADJ Jelly par profile sys User Manual download pdf (Page 5)

©American DJ® - www.Americandj.com - Mega Par Prole User Manual Page 10©American DJ® - www.Americandj.com - Mega Par Prole User Manual Page 9

Mega Par Profile Operating Instructions

UP and DOWN buttons to adjust intensity.

5. After you have adjusted the RGB colors to make your desired color

you can then activate strobing by pressing the SET UP button to

enter the Flash (strobe) mode.

6. “FS.XX” will be displayed, this is Flash mode. The Flash can be

adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

DMX Mode:

Operating through a DMX controller gives the user the freedom to create

their own programs tailored to their own individual needs. This function

also allows you to use your fixtures as spot lights. The Mega Par Profile

has 7 DMX modes: 1 Channel mode, 2 Channel mode, 3 Channel mode,

4 Channel mode, 5 Channel mode, 6 Channel mode, and a 7 Channel

mode. See pages 13-16 for each modes’ DMX traits.

1. This function will allow you to control each individual fixture’s traits

with a standard DMX 512 controller.

2. To run your fixture in DMX mode press the MODE button until

“A.XXX” is displayed. “XXX” represents the current displayed ad-

dress. Use the UP or DOWN buttons to select your desired DMX

address, then press the SETUP button to select your DMX Channel

mode.

3. Use the UP or DOWN buttons to scroll through the DMX Channel

modes. The Channel modes are listed below:

To run the 1 Channel Mode, press the MODE button until “Ch.01”

is displayed. This is the 1 Channel DMX Mode.

To run the 2 Channel Mode, press the MODE button until “Ch.02”

is displayed. This is the 2 Channel DMX Mode.

To run the 3 Channel Mode, press the MODE button until “Ch.03”

is displayed. This is the 3 Channel DMX Mode.

To run the 4 Channel Mode, press the MODE button until “Ch.04”

is displayed. This is the 4 Channel DMX Mode.

To run the 5 Channel Mode, press the MODE button until “Ch.05”

is displayed. This is the 5 Channel DMX Mode.

To run the 6 Channel Mode, press the MODE button until “Ch.06”

is displayed. This is the 6 Channel DMX Mode.

To run the 7 Channel Mode, press the MODE button until “Ch.07”

is displayed. This is the 7 Channel DMX Mode.

4. Please see pages 13-16 for DMX values and traits.

5. After you have chosen your desired DMX Channel mode plug in

the fixture via the XLR connections to any standard DMX controller.

Mega Par Profile Operating Instructions

Default Running Mode:

This is a default running mode. When this mode is activated all modes

will return to their default settings.

1. Plug the fixture in and press the MODE button until “dXX” is dis-

played. “XX” represents either “on” or “oFF”.

2. Press the SET UP button until “dEFA” is displayed.

3. Press the UP and DOWN buttons simultaneously. Press the MODE

button to exit.

ADJ LED RC:

This function is used to activate and deactivate the ADJ LED RC

(Remote Control). When this function is activated you can control the

fixture using the ADJ LED RC. Please see the next page for ADJ LED

RC controls and functions.

1. Plug the fixture in and press the MODE button until “dXX” is dis-

played. “XX” represents either “on” or “oFF”.

2. Press the SET UP button until “IrXX” is displayed. “XX” represents

either “on” or “oF”.

3. Press the UP or DOWN buttons to either activate the remote func-

tion (On) or deactivate it (Off).

Master-Slave Configuration:

This function will allows you to link units together to run in a Master-Slave

mode. In Master-Slave operation one unit will act as the controlling unit

and the others will react to the controlling units built-in programs. Any

unit can act as a Master or as a Slave however, only one unit can be pro-

grammed to act as the “Master.”

Master-Slave Connections and Settings:

1. Daisy chain your units via the XLR connector on the rear of the unit.

Use standard XLR data cables to link your units together. Remember

that the Male XLR connector is the input and the Female XLR con-

nector is the ouput. The first unit in the chain (master) will use the

female XLR connector only. The last unit in the chain will use the

male XLR connector only.

2. Connect the rst “Slave” unit to the “Master.”

3. Set the “Master” unit to your desired mode of operation. The “Slave”

unit will now follow the “Master”.

Mega Par Profile Master-Slave Configuration

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

ADJ Jelly par profile sys User Manual Page 5

Comments to this Manuals

Related products and manuals for Floodlights ADJ Jelly par profile sys